Draw the Gauge Reach Before You Approve a Blind Keyway

A blind keyway may look complete when viewed from the open end of a hub, yet the most consequential section can be the one the inspector cannot reach. A straight gauge enters cleanly, stops before the closed end and returns a satisfactory result. That result says something about the region the gauge contacted; it does not automatically confirm the last portion of the slot was cut to full depth.

Blind keyway inspection access should be established while the drawing and machining method are being selected. Show the required full-depth length, the actual end contour and the proposed gauge's contact envelope on the same section. If the gauge cannot examine the required end region, the design and quality owners need to approve another method or revise the requirement before signing off the part.

Distinguish three lengths on a closed-end feature

A dimension that says 'keyway depth' may refer to radial depth, while a note saying 'slot length' refers to distance along the bore. The drawing should identify both without forcing the machinist or inspector to infer one from the other. On a closed-end feature, also separate the last fully formed cross-section from the final visible curve or tool runout.

Required usable length

The design owner defines how far the keyway must maintain the specified width and radial depth so the mating key can perform its intended function. This is the controlled full-depth portion; it is not necessarily the distance to the furthest visible mark left by the cutter.

Actual cut end

The machining process may leave an end radius, transition or permitted relief. Its shape and location matter because a profile can taper or curve before it terminates. Do not replace this information with a generic 'blind broach to bottom' instruction. The supplier needs the accepted end geometry and any clearance needed by the selected tool.

Usable gauge reach

A physical gauge has a tip shape, contact faces, body and possible shoulder. Its ability to reach the last full-depth segment depends on those features and the bore geometry. A gauge that appears narrow at the tip may still stop when another part of its body contacts the bore or end contour.

One section with F, E and G marked

Figure 1 is an original schematic section of a fictional blind keyway. F is the last required full-depth location, E is the closing contour, and G shows where an illustrative contact gauge stops. The distance from the entrance to G is shorter than the distance to F. No dimensions, tolerance or approved relief are asserted by the drawing.

 

Figure 1. Illustrative blind-keyway section with last full-depth point F, end contour E and gauge contact reach G; schematic only.

The visible gap between G and F is the inspection question, not an automatic nonconformance. If the approved inspection method must directly contact the full-depth region through F, the shown gauge is insufficient. If another qualified method can evaluate that region, the quality owner should document how it establishes compliance and any limits of confidence.

Ask which surface the gauge actually touches

A width check at the slot entrance may miss an out-of-spec portion at the closed end. A depth check using the bore wall as reference may be affected by the end contour or insufficient probe travel. State where the gauge contacts the flank, the floor and the feature datum. Do not write 'gauge passes' without naming the inspected interval.

Where the drawing calls for a go/no-go check, confirm that the selected gauge geometry matches the controlled profile and that its path is not blocked before the acceptance region. Other approaches—such as an approved probe, replica, sectioned sample or optical method—could be considered by the responsible metrology team, but no substitute should be treated as equivalent without qualification and approval.

Access is not only a machining concern. Cleaning chips from a closed-end feature, checking its floor and photographing its contour may require different tools. Ask for inspection and cleaning access during design review rather than assuming a finished slot can always be checked using a standard gauge.

Use a drawing review card before placing the order

The following fictional record makes the uncertainty clear and avoids invented dimensions.

GEOMETRY — Internal blind keyway K-B in hub H-EX; bore and part datum per drawing revision C; actual dimensions to be supplied.

FULL-DEPTH — Location F defined by design; specified width and radial depth must be maintained to F.

END — Contour E and any allowable relief or radius not yet confirmed by design.

GAUGE — Candidate tool G reaches only part of specified zone in the mock section; gauge model/contact shape unresolved.

METHOD — Quality owner to approve how the interval from G to F will be verified, or request an engineering revision.

STATUS — HOLD for drawing and inspection clarification; no manufacturing acceptance implied.

This record should accompany the revision that a machine shop uses for its quotation. A 'hold' is not a claim that the design is impossible. It means the information needed to create and inspect the specified feature has not yet been completed.

Review the machining route with inspection in mind

An internal blind slot can require different tool motion and chip management from a through-cut feature. The process engineer must review the selected cutter, rigidity, bottom clearance and how material leaves the closed end. A process that can create the geometry must still allow the specified result to be verified.

Broaching Technologies, LLC describes blind keyway and spline machining using C.A.M.S. vertical slotting equipment at its Menomonee Falls, Wisconsin operation. The service overview discusses controlled cutting depth and chip evacuation; it does not promise that a particular inaccessible end region can be verified with any gauge the buyer happens to own.

When comparing machining for blind keyways and splines, send the same section with F, E and G marked. Ask the supplier to identify its attainable end geometry, any proposed tool runout, and which inspection views or measurement features it can provide. Keep any proposed relief subject to the design owner's approval rather than assuming that a larger relief is always harmless.

Make the signoff question unambiguous

At drawing release, ask: 'Can the approved inspection method verify the specified full-depth keyway through location F without interference from end contour E, and who has accepted the method's limitations?' Record the answer, drawing revision and signoff owner. If the answer is no or unknown, hold the inspection plan and return it to design.

A blind keyway is ready for quotation when the functional length, tool-end geometry and verification method are described as one consistent requirement. The part's closed end may be hidden from view, but the inspection decision should not be.

 


Google AdSense Ad (Box)

Comments